When the 4-speaker layout is selected, 7-band parametric equalizers can be adjusted.
When the 3 way speaker layout is selected, 11-band parametric equalizers can be adjusted for the Hi range, Mid range and Low range.
(For details on speaker layout setting, Speaker layout settings (SP Layout).)
Each band can be set to the following median frequencies:
When the 4-speaker layout is selected
Band | Adjustable frequency (Hz) |
---|---|
1 | 63, 80, 100 |
2 | 125, 160, 200 |
3 | 250, 315, 400, 500 |
4 | 630, 800, 1 k, 1.25 k |
5 | 1.6 k, 2 k, 2.5 k, 3.15 k |
6 | 4 k, 5 k, 6.3 k, 8 k |
7 | 10 k, 12.5 k, 16 k |
When the 3 way speaker layout is selected
Channel | Band | Adjustable frequency (Hz) |
---|---|---|
Hi | Hi 1 | 200, 250, 315, 400, 500, 630, 800, 1 k, 1.25 k, 1.6 k, 2 k, 2.5 k, 3.15 k, 4 k, 5 k, 6.3 k, 8 k, 10 k, 12.5 k, 16 k |
Hi 2 | ||
Hi 3 | ||
Hi 4 | ||
Hi 5 | ||
Mid | Mid 1 | 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 800, 1 k, 1.25 k, 1.6 k, 2 k, 2.5 k, 3.15 k, 4 k, 5 k, 6.3 k, 8 k, 10 k, 12.5 k, 16 k |
Mid 2 | ||
Mid 3 | ||
Mid 4 | ||
Mid 5 | ||
Low | Low | 20, 25, 31.5, 40, 50, 63, 80, 100, 125, 160, 200, 250 |
Press the [SELECT] (Up/Down) button to select PEQ.
Press the [ENTER] button.
The PEQ setting mode is activated.
Press the [ENTER] button to select the band to be adjusted.
Each time the button is pressed, the band changes in the following order.
When the 4-speaker layout is selected:
1 → 2 → 3 → 4 → 5 → 6 → 7 → 1 →···
When the 3 way speaker layout is selected:
Hi 1 → Hi 2 → Hi 3 → Hi 4 → Hi 5 → Mid 1 → Mid 2 → Mid 3 → Mid 4 → Mid 5 → Low → Hi 1 →···
Press the [SELECT] (Right/Left) button to select the frequency to be adjusted.
Press the [SELECT] (Up/Down) button for less than one second to adjust the frequency level.
Up :
Increases the level.
Down :
Decreases the level.
Press the [SELECT] (Up/Down) button for more than one second to adjust the Q curve pattern.
Each time the button is pressed, the Q curve pattern changes in the following order.
WIDE ↔ Mid WIDE ↔ NORMAL ↔Mid NARROW ↔ NARROW ↔WIDE ↔···
Repeat the steps 3 to 6 to change the settings for each channel and band.
Press a button from [1] to [5] for more than two seconds to preset a setting value.
The preset value is overwritten by the value set using the above steps.
The time alignment and crossover adjustments will also be stored at this time.