Adjusting Sound
Adjusting Volume
1.
Turn the [VOL] rotary knob.
Turn to the right: Increases the volume.
Turn to the left: Decreases the volume.
Do not adjust the volume or other controls while driving the vehicle. Do so only while parked in a
safe location.
Page Top
Muting the Volume
1.
Press the [MUTE] button.
To cancel muting, either press the [MUTE] button again or turn the [VOL] rotary knob to
the right.
While the audio system is muted, navigation voice guidance continues unmuted.
Page Top
Setting Guide Tone
1.
Press the [FUNC] button to establish the FUNCTION mode.
2.
Press the [FUNC] button until the indication on the sub display switches to
BEEP.
3.
Press the [SELECT (Right/Left)] button to switch between ON and OFF statuses
for BEEP.
Right : ON
Left : OFF
4.
Press the [ENTER] button.
Page Top
Switching Audio Control Modes
1.
Modes will switch in the order shown below each time the [ENTER] button is
pressed.
BASS -> MID -> TREB -> BAL -> FAD -> NON-F -> NF-P -> LPF -> LOUD -> SVC ->
BASS -> ...
Turn the [VOL] rotary knob to the right or left in the audio mode while referring to the table below to adjust the
sound.
|
Mode
|
Function
|
[VOL] rotary knob/Function
|
|
BASS
|
Adjusts bass level.
|
Turn to the right
|
Emphasizes low sounds.
|
|
Turn to the left
|
Softens low sounds.
|
|
MID (MIDDLE)
|
Adjusts middle level.
|
Turn to the right
|
Emphasizes mid range sounds.
|
|
Turn to the left
|
Softens mid range sounds.
|
|
TREB (TREBLE)
|
Adjusts treble level.
|
Turn to the right
|
Emphasizes high sounds.
|
|
Turn to the left
|
Softens high sounds.
|
|
BAL (BALANCE)
|
Adjusts left/right (BALANCE) speaker balance.
|
Turn to the right
|
Emphasizes right speakers.
|
|
Turn to the left
|
Emphasizes left speakers.
|
|
FAD (FADER)
|
Adjusts front/rear (FADER) speaker balance.
|
Turn to the right
|
Emphasizes front speakers.
|
|
Turn to the left
|
Emphasizes rear speakers.
|
|
NON-F (NON-FADER LEVEL)
|
Adjusts non-fader level (for connected sub-woofer).
|
Turn to the right
|
Increases the sub-woofer level.
|
|
Turn to the left
|
Decreases the sub-woofer level.
|
|
NF-P (NON-FADER PHASE)
|
The merger of sound between the front and rear speakers and the woofer can be improved by selecting the phase. Switch the phase which lets the speakers combine without any disharmony.
|
Turn to the right
|
NORMAL
(Make the output timing of the front/rear speakers and the woofer the same.)
|
|
Turn to the left
|
REVERSE
(Change the phase of the output timing of the front/rear speakers and the woofer.)
|
|
LPF (Low Pass Filter for Sub-Woofer output)
|
Adjust frequency filtering settings.
|
Turn to the right
|
LPF ON :
Only allow lower frequencies (low range) through.
|
|
Turn to the left
|
LPF OFF :
Allow all frequencies through regardless if the frequencies are low or high.
|
|
LOUD (LOUDNESS)
|
Accentuate low and high frequencies when the volume is low.
When loudness is ON, the apparent deficiency in the high sounds is compensated for.
|
Turn to the right
|
ON
|
|
Turn to the left
|
OFF
|
|
SVC (Source Volume Control)
|
Set the volume for each of the audio sources. (except for FM)
|
Turn to the right
|
Increase the SVC setting level.
|
|
Turn to the left
|
Decrease the SVC setting level.
|
